Subscribe to:
Post Comments (Atom)
Last 7-day Most Viewed Pages
-
I used to have a problem with my earlier Peugeot [not 308] AL4-Transmission. It was under warranty, so it didn't incur any direct cost t...
-
There are about a dozen of steps to follow before the battery can be removed. Of course the bonnet must be opened first la... Tools neede...
-
Click HERE to watch all Videos
-
What your Service Centers normally don't tell you! I never send my cars to any workshop when "Depollution System Faulty" ...
-
Not everybody knows exactly where the oil filter cartridge housing is located. It is actually hidden underneath air intake flexible hose. ...
-
How to Identify Imitation Spark Plugs? [from NGK website] click on the image to enlarge When I checked the factory fitted NGK platinum...
-
All the while I had been thinking the battery was the culprit every time the starter motor didn't do its job. But the battery works fin...
-
Light beams should be realigned every time after bulbs replacement to avoid causing a nuisance to other road users . The only tools require...
-
Lately my308 has developed knocking or pinging sound during hard acceleration at speeds around 50km/hr. The problem persists even after usi...
-
Blog name has been changed to " one.D'rive ". Formerly it was "AHW308" Meanwhile, I'm going back to reading...
All-time Most Popular Posts
-
All the while I had been thinking the battery was the culprit every time the starter motor didn't do its job. But the battery works fin...
-
Not everybody knows exactly where the oil filter cartridge housing is located. It is actually hidden underneath air intake flexible hose. ...
-
There are about a dozen of steps to follow before the battery can be removed. Of course the bonnet must be opened first la... Tools neede...
-
I used to have a problem with my earlier Peugeot [not 308] AL4-Transmission. It was under warranty, so it didn't incur any direct cost t...
-
Everybody wants to save fuel, but there're lots and lots of incorrect advices I found on local and international motorcar forums on how ...
-
If you have a Peugeot powered by EP6-DT* engine, sooner or later there is a chance for you to experience "Intermittent Power Loss"...
-
Prerequisite: u must be able to know how to remove car wheel and have knowledge on how to remove/replace front brake pads. If not pls visi...
-
Light beams should be realigned every time after bulbs replacement to avoid causing a nuisance to other road users . The only tools require...
-
Step 1 HID conversion kit installation begins with the HARDEST step, i.e choosing and picking out the right HID kit - there is a large r...
-
I've been observing "Super Knocking" is a common problem associated with EP6-DT* engines. At the beginning it is not easy t...
7 comments:
I have a bluetooth version. And im uaing android app torque pro....recently have engine rattling tak tak tak when accelerate from 50km/h.... try to scan fault code of super knock.... cant find any... missing some configuration?
It could be faulty knock sensor. I had similar knocking problem developed recently and I used eTuner Lionheart free software and it tells exactly what went wrong. After replacing the knock sensor @RM350 the problem solved. No more pinging even on RON95 fuel.
eTuner Lionheart does noy support bluetooth interface unfortunately.
I'm not sure about the bluetooth. I'm using USB dongle with a laptop running on windows XP operating system. No problem.
bro, i need some advice. Saw your post about DIY, testing both the batt & alternator. My alternator is measuring 12.8-13.1v when the engine is in idle mode. Even when i rev up to 2krpm, it does not change the voltage. SC had changed a new alternator for me but the voltage 'retirned' to the same range of 12.8-13.1v a few days later. My battery is not fully charge, its between 12.3v-12.5v, so i am running out of idea why the charging voltage is so low. I need help, SC is not helpful at all...
one more thing, since i can check the voltage when i am driving, i do have a OBDII connected. I notice the charging is higher when i am decelerating..!why terbalik??!
As salam,
Just wondering, I managed to get diagbox v7.30 (dapat free from the internet), but I dont have the interface tool/VCI cable. In your opnion, does the 'china made' elm327/OBD2 usb cable work with this software. Sebab, kalau ok baru nak beli cable tu. Kat ebay jual interface tool tu around RM250-400.
Post a Comment