1. Get the tools and materials required...
... wire cutter, long-nose plier, soldering iron, soldering lead, super bright white LEDs, 1157 base, etc
2. Solder four_LEDs in series for DRL circuit like this...
[observe where are the cathodes and the anodes], and for the sidelight solder four LEDs like this...
All together u need six sets for the DRL and one set for side light for each 1157 conversion bulb.
3. Solder each LED cathode to the 1157 base
4. Solder all the anodes together and reinforce the cathodes
5. Test....
6. Connect the anode to the base terminal using an insulated wire.
7. Solder the LED set for the side-light around the lower part of the DRL LED cluster to finish the 'assembly'.
8. Install the DIY LED conversion bulb and test run....
Related Topic on LEDs
Frequently Visited Pages:
| Home | Fuel Consumption | Performance | uncle's DIY |
Car Size Comparison | Motoring Myths | RON95 |
Subscribe to:
Post Comments (Atom)
Last 7-day Most Viewed Pages
-
Everybody wants to save fuel, but there're lots and lots of incorrect advices I found on local and international motorcar forums on how ...
-
All the while I had been thinking the battery was the culprit every time the starter motor didn't do its job. But the battery works fin...
-
Light beams should be realigned every time after bulbs replacement to avoid causing a nuisance to other road users . The only tools require...
-
I used to have a problem with my earlier Peugeot [not 308] AL4-Transmission. It was under warranty, so it didn't incur any direct cost t...
-
What is Camber? The camber is the angle, measured in degrees, between the center line of the wheel and the perpendicular to the ground, look...
-
There are about a dozen of steps to follow before the battery can be removed. Of course the bonnet must be opened first la... Tools neede...
-
Traditionally more displacement [engine capacity] means more power because it can burn more fuel during each revolution of the engine. Disp...
-
What your Service Centers normally don't tell you! I never send my cars to any workshop when "Depollution System Faulty" ...
-
Don't throw away your Depleted Fragrance Cartridge. You can reuse it for something that look a little canggih . You can use it as a nice...
-
The 'black box', as I prefer to call it can either contain nothing more than resistors with some electronic switching circuits with...
All-time Most Popular Posts
-
All the while I had been thinking the battery was the culprit every time the starter motor didn't do its job. But the battery works fin...
-
Not everybody knows exactly where the oil filter cartridge housing is located. It is actually hidden underneath air intake flexible hose. ...
-
There are about a dozen of steps to follow before the battery can be removed. Of course the bonnet must be opened first la... Tools neede...
-
I used to have a problem with my earlier Peugeot [not 308] AL4-Transmission. It was under warranty, so it didn't incur any direct cost t...
-
Everybody wants to save fuel, but there're lots and lots of incorrect advices I found on local and international motorcar forums on how ...
-
If you have a Peugeot powered by EP6-DT* engine, sooner or later there is a chance for you to experience "Intermittent Power Loss"...
-
Prerequisite: u must be able to know how to remove car wheel and have knowledge on how to remove/replace front brake pads. If not pls visi...
-
Light beams should be realigned every time after bulbs replacement to avoid causing a nuisance to other road users . The only tools require...
-
Step 1 HID conversion kit installation begins with the HARDEST step, i.e choosing and picking out the right HID kit - there is a large r...
-
I've been observing "Super Knocking" is a common problem associated with EP6-DT* engines. At the beginning it is not easy t...
7 comments:
kudos to our uncle Ahwan,man with a golden touch...
is this brighter than your previous creation?
canggih..
azhelmy, aslan308: Soldering used to be part of my jobs. He heee....
Verm: They're better than previous versions...
great. thx.
how's the power consumption?
Bila nak buka kedai ni? ramai tunggu nak buat tu....:)
nice work . I like it
You are most welcome :)
Post a Comment